|
Sell LED curing light(YS-B-I)
|
Pageviews: 241
|
YS-B-I
1. Product introduction
This product is used in fast solidification by lighting dental resin.
It is a new generation of standard developed LED curing light, with humanity intelligent chip, the world advanced high intensity LED light and Li-on rechargeable battery, which is based on YY0055-2002 《Curing Light》. It can cure all the dental resin in the market nowadays, Its performance is further surpass the halogen curing light's, which can solidify 4-5mm deepness in 20 seconds.
2. Standard accessories
1.Curing light + high capacitance rechargeable battery (each one set)
2.Special charger + special charger socket (each one set)
3.Operation manual and maintenance card
3. Technical parameters
Power voltage AC100-240V 50-60Hz
Input power 5W
Light intensity 550mw/cm2
Wavelength 400-500mm
Model and signification Model YS-B-I
YS— Curing light product symbol of our company
B-I— Model B-I
4. Installation instructions
Please follow the below
1.Plug the charger to the net power socket, the indicator light is on.
2.Put the charg 1. Product introduction
This product is used in fast solidification by lighting dental resin.
It is a new generation of standard developed LED curing light, with humanity intelligent chip, the world advanced high intensity LED light and Li-on rechargeable battery, which is based on YY0055-2002 《Curing Light》. It can cure all the dental resin in the market nowadays, Its performance is further surpass the halogen curing light's, which can solidify 4-5mm deepness in 20 seconds.
2. Standard accessories
1.Curing light + high capacitance rechargeable battery (each one set)
2.Special charger + special charger socket (each one set)
3.Operation manual and maintenance card
3. Technical parameters
Power voltage AC100-240V 50-60Hz
Input power 5W
Light intensity 550mw/cm2
Wavelength 400-500mm
Model and signification Model YS-B-I
YS— Curing light product symbol of our company
B-I— Model B-I
4. Installation instructions
Please follow the below
1.Plug the charger to the net power socket, the indicator light is on.
2.Put the charge socket on a horizontal plane, connect with the charger pin the indicator light is on.
3.Put the Curing Light into the charger socket.
Operation
Connect the front of handpiece with the lamp guide and press the power button under the mode of power-off , if the power source indicator light is on, that means the battery is well installed, the curing light will work normally.
The first operating mode is settled as the default one, called shining function, press the power button the curing light will work under the default mode, and it will turn off in 20 seconds automatically, then turn to the standing idle.
During the standing idle you can change the operating mode by pressing the selection button in a circle. The second operating mode is gradually shinning function, the light of the LED will get stronger and stronger during the early 12 seconds. The third mode is gleam shining function. The sound of indicator and the standing idle of all the three modes are the same, the LED will stop to enter the standing idle in 20 seconds and it will turn off automatically without any operation in 3 minutes, and then all the indicator lights turn off. In this condition pressing the power button can wake up the curing light, entering the standing idle.
Time of cure the dental resin, please refer to the introduction.
Charge
If the power of the curing light is not enough during the operation, it should be charged immediately. You should put the curing light into the charger socket, if the indicator light turns blue, that means the LED curing light is well connected. (If not ,you can circumvolve it or clean the charger board with alcohol ) then connect the power source, when the light turns green it means charge, while it is yellow it means that it is fully changed.
☆ Cover the curing light with the one-off asepsis plastic bag before use.
5. Precaution
1. The cuing light can not be used continually over 3 minutes.
2. The curing light can not dip in the liquid or close to the fire.
3. Avoid collision and extrusion by outside force.
4. It can not be knocked down without permission. Or, we do not offer the guarantee.
5. If you have any other problems, please contact our supplier.
Caution: the curing light cant not be pointed at the patient's eyes while it is operating. if any accidents happen, go to the hospital immediately.
6. Storage introduction
This equipment should be stored under the following conditions:
Temperature :-20°C～40°C
Humidity :≤85%
7. Structure and pars
green it means charge, while it is yellow it means that it is fully changed.
☆ Cover the curing light with the one-off asepsis plastic bag before use.
8. Maintenance
Put the LED into the charger socket when not in use, connect with the power source when necessary.
If the battery is not used for long time, charge the battery every 15 days.
The power should be cut off within two hours when the battery is fully charged, or it will damage the battery.
9. After Service
We warrant this equipment against defects or workmanship for a period of one year from the date of purchase with the maintenance card. It includes: free material cost; back and forward mail delivery cost and maintenance cost, but we do not offer maintenance extension services.
Do connect the supplier in time when the equipment conks out, you may send it with the maintenance card directly or by mail to our company or our franchiser.
If the overdue product's seal is still intact, just material cost, back forward mail delivery cost is necessary, no any maintain fee is needed.
Buyer should fill in the blanks in the maintenance card carefully after purchase.
The following conditions are not in the free maintenance service
Maintenance card is changed or lost
Seal is damaged, private disconnection results in mangle.
Operation in incorrect way results in mangle, such as: connect incorrect power supply, collision by outside force, extrusion, falling etc.
Damage by force majeure: earthquake or other nature disasters.
Using the fitting spare parts from other companies causes the mangle.
10. Electric connection figure
|
|
Contact Information of poster
| Company Name: |
Foshan Yunsheng Medical Instrument Co.,Ltd |
| Contact Person: |
LIU KUN |
| Address: |
shakeng Industry area, Luocun town Nanhai, Foshan City, China |
| Country |
, cn  |
| Zip Code: |
528000 |
| Homepage |
www.fsyunsheng.com |
| About Foshan Yunsheng Medical Instrument Co.,Ltd: |
Foshan Yunsheng Medical Instrument Co.,Ltd is specialize in developing, exploiting and manufacturing different kinds of Dental Products.
We are working ourself to supply many kinds of LED Curing Light, High Speed Handpiece, Air Compressor, and other a lot more. Moreover, collaborate with other enterprises, we enlarge our business line to X-Ray Unit, Autoclave and Detal Chair Unit and so on.
Taking “Quality is Root, Customer is God” as our company principle. We sincerelly look forward to your corporations with our excellent service, high quality and favorable price in the market.
|
|
|
Statistics for "Sell LED curing light(YS-B-I)":
|
| Detailed Pageviews:
|
241 ( number of times this page was viewed)
|
|
Last Update:
|
2006-12-21 02:12:41
|
More Import/Export Wholesale Leads trade leads ...
|
| |
Medical, Dental and Surgical 
Alcoa launches extreme temperature training
sell QDGY brand auto brake hose
Methanol Tablets, Eurochemlabs, pack: 100 tablets 10mg/tabl
Refined coconut oil
Brand new mosquito control product
T & C PROJECT CO., LTD.
Peruvian Silver Handmade Jewelry
Sony PSP Value pack
spearmint leaves whole
split unit air conditioner
Accident Compensation - Why Bother With A Claim?
Subaru Impreza STi WRX RA
Medicinal Herbs and Powdered Herbal Extracts
Forever Blue Light Torch EA002
sell HP,CANON,LEXMARK,EPSON compatible ink cartridge
dyestuff